본문 바로가기

카테고리 없음

Installing Exhaust Hanger

Our heavy duty rubber hangers have an added center piece that helps the rubber from jumping off the curved hooks when you go over heavy bumps. To save time just cut the old hangars off but do it one at a time or your exhaust system will drop down on your head!Putting new donuts on is a little tricky. They are too stiff to stretch by hand. Install one end first and firmly seat in place. Use a flat blade screwdriver and put it through the other end. Then place the tip of the screw driver on the center of tip of the other metal hook and pry the donut up and over onto until it snaps into place.Recommended products.

  1. Installing Exhaust Hangers

AmericanMuscle is proud to offer FREE SHIPPING on any order over $49!Free Shipping Offers are for Standard Ground Delivery service and are only valid for shipping addresses within the 48 Contiguous United States. Truck freight and oversize charges still apply unless otherwise notes and can only be shipped to the lower 48 States.Same Day Shipping (on most parts) if you order by 5PM EST on a business day. We ship via UPS Ground and/or USPS to all locations in the Continental 48 States.AmericanMuscle also offers Free Freight Handling to locations with loading docks in the Continental 48 States. Freight shipments going to a residential address will require a $75 residential handling fee.Estimated delivery times for Standard Shipping:. East Coast, 1-3 business days. Midwest, 2-4 business days.

Hangers

Southwest, 3-5 business days. West Coast, 4-6 business daysFor full shipping details please view our. Prior to lifting vehicle ensure vehicle is locked in gear and emergency parking brake is fully engaged with wheel chock placed behind rear wheels.2. Proceed to raise vehicle with floor jack and place jack stands under vehicle recommended jacking points securely and lower.3. Locate exhaust bracket bungs on frame rail.4.

Using a 8MM x 1.25 tap proceed to apply small amount of cutting oil to the cutting threads and align T-handle 90 degree’s with bottom frame rail bungs. Slowly turn until tap is half way through and carefully back out tap and remove any metal shaving. (Only required on V6 Mustang models driver side only.).

NOTE: To adjust for height your muffler has to be removed from vehicle. You should allow for.

Gap for spacing to prevent damage to plastic bumper cover due to movement while driving.Low hanging: If your muffler is hanging lower than one quarter of inch. Proceed to bend rear hanging rod downward with a pipe adding a slightly down bend will help lift closer to bumper cover.Muffler touching bumper cover: Adding a slight upward bend to the rear rod will allow for clearance and give a gap between the muffler and body cover and avoid mufflers tips melting cover and damage from movement while driving.Installation Instructions Written By AmericanMuscle Customer Ryan Maguire Best Sellers. Mustang Specs By Year. 2019. 2018.

2017. 2016.

2015. 2014.

Installing Exhaust Hangers

2013. 2012. 2011. 2010. 2009. 2008.

2007. 2006. 2005. 2004. 2003.

2002. 2001. 2000.

1999. 1998. 1997. 1996.

1995. 1994. 1993.

1992. 1991. 1990. 1989. 1988.

1987. 1986. 1985.

1984. 1983. 1982. 1981. 1980. 1979. Shelby GT500.

2013-2014 Shelby GT500. 2010-2012 Shelby GT500. 2007-2009 Shelby GT500. SVT Cobra. 2003-2004 SVT Cobra. 1999-2001 SVT Cobra.

1996-1998 SVT Cobra. 1994-1995 SVT Cobra. 1993 SVT Cobra. Bullitt. 2008-2009 Bullitt. 2001 Bullitt.

2003-2004 Mach 1. FORD, FORD MUSTANG, MUSTANG GT, SVT COBRA, MACH 1 MUSTANG, SHELBY GT 500, COBRA R, BULLITT MUSTANG, SN95, S197, V6 MUSTANG, FOX BODY MUSTANG, AND 5.0 MUSTANG ARE REGISTERED TRADEMARKS OF FORD MOTOR COMPANY. Dodge, Dodge Challenger, SRT8, R/T, Rallye Redline, Scat Pack, SRT Hellcat, SRT Demon, T/A, Pentastar, and Hemi are registered trademarks of Fiat Chrysler Automobiles (FCA). SALEEN IS A REGISTERED TRADEMARK OF SALEEN INCORPORATED. ROUSH IS A REGISTERED TRADEMARK OF ROUSH ENTERPRISES, INC. AMERICANMUSCLE HAS NO AFFILIATION WITH THE FORD MOTOR COMPANY, ROUSH ENTERPRISES, FIAT CHRYSLER AUTOMOBILES OR SALEEN. THROUGHOUT OUR WEBSITE AND MUSTANG CATALOG THESE TERMS ARE USED FOR IDENTIFICATION PURPOSES ONLY.